How To Repair Torn Leather Seat In Car
To the left is a leather seat from an MR2, as can be seen, with years of apply it has suffered meaning harm to the left hand side The friction caused past rubbing against the leather has, over the years, resulted in a hole being made and a lot of abrasion to the surface. The below guide is intended to teach you near leather automobile seat repair, specifically showing you how to repair a hole in a leather car seat.
PRODUCTS REQUIRED
- Leather Repair Kit - To Repair the hole. This kit as well contains a pocket-sized amount of color, so tin can be used on its ain to repair minor areas of damage on a leather car seat.
- Minor Leather Colourant Kit - Used to restore the leather color to the whole bolster.
Nosotros also have a total pick of Leather Automobile Seat Repair products on our website.
Leather Car Seat Repair Method
STEP 1. Prepare the leather car seat
The beginning step it to prepare the leather for repair. Using the Leather Prep & abrasive pad, included in the Colourant Kit, gently rub the surface of the leather to remove any grease and oils that have accumulated.
This step volition also remove whatsoever loose fibres and remove the manufactured cease allowing the colourant, applied later in this tutorial, to adhere to the leather properly.
After prepping, wipe the leather downwards with the Alcohol Cleaner, this volition remove any dirt or grit from the expanse before moving on to the next step.
Footstep ii. Tidy the area
If you expect at the hole you can see that the leather is sticking outwards, like a lip. This lip will compromise the quality of the repair and it should be removed.
Using the scalpel or a pair of scissors, carefully remove the lip past cut it abroad at the base, taking care not to damage the surrounding leather.
STEP 3. Apply the backing patch
In guild to provide a firm bankroll for the repair, the leather repair sub-patch should be practical. Take the patch supplied in the kit and cut it to size, it should be enough to completely embrace the repair with an additional 1cm of material surrounding the hole.
In one case this is washed use the tweezers to insert one side of the patch underneath the leather and so that the 1cm excess is completely under the leather. Utilize force per unit area to hold this in place and gently feed the patch under the remaining edges of the pigsty. When done the patch should prevarication flat nether the repair, and the 1cm surrounding material we left should exist underneath the leather on all sides.
When this is washed, put a small amount of Leather Glue onto the spatula supplied and feed this underneath the edges of the hole to glaze the underside of the leather surrounding it, taking care not to move the canvass patch. When all edges have been glued, utilize pressure to bail the leather to the patch and allow to dry out.
Step iv. Fill the hole
Now that the backing patch is firmly in place, the hole in the leather must be filled. In order to practise this; take a small amount of the Heavy Filler using the cease of the palette knife and place a sparse layer into the hole over the bankroll patch. Make sure all the layer is very thin, only roofing the sub-patch and let xx minutes to dry out, this can be speeded up by using a hair dryer.
Keep applying the heavy filler in thin layers, it is crucial to use thin layers equally the filler shrinks as it dries and may not cure properly if the layers applied are likewise thick. Equally a full general dominion, at to the lowest degree 5-six sparse layers should be used to build up the filler until the filler level is congenital upward to just below the summit of the hole.
To remove excess, with the application of each layer, smooth the area over with the sharper edge of the palette pocketknife earlier drying the layer practical.
Footstep 5. More Layers of Filler
This is an illustration of what the hole will look like subsequently five or half dozen layers of filler take been used.
It will not exist smooth but it will accept most filled the pigsty completely.
STEP 6. Add the terminal layer of filler
Use the final layer of filler to the hole, completely filling it so that it is on an even level with the surrounding leather on the seat. Take care to let this concluding layer cure properly as when cured the filler tin compress, reducing it to below the desired level.
Add together more repair filler if necessary.
If y'all rub over the pigsty and filler gets onto the leather, remove it with the palette pocketknife.
Your aim is to fill the hole so that it is level with the leather and non over filled. If you practice over fill it, yous can reduce it with sandpaper.
When you are happy with the level of the filler, and yous can no longer feel any 'ridge' between the level of the filler and the surrounding leather, clean the area with the Booze cleaner once again to remove any unwanted filler and grit from the surrounding area.
Pace 7. Employ an initial coat of colourant
The colourant supplied with the kit should have been matched to the color of the leather item being repaired, unless you lot are completely re-colouring it.
Take one of the sponges supplied in the kit and apply a pocket-sized amount of colourant to it, then rub this into the area of the repair thoroughly. This allows the colourant to penetrate into the creases of the leather and valleys of the grain, giving a better overall finish.
When this is washed, motility onto the adjacent footstep, where the colourant is sprayed on.
STEP 8. Finish the job
Using an airbrush spray as many thin coats of colour over the leather car seat to thoroughly alloy in the repair. For the best result, ensure that each glaze is very thin and is given sufficient time to cure before applying the next. This will enable an even finish to be congenital up and will avoid problems with uncured colourant. It is not uncommon for the best repairs to utilise 10-fifteen thin coats of colourant, depending on the extent of the damage and the colour used.
One time you are happy that the repair is concealed, the colourant is cured properly and it is well composite with the surrounding leather, the terminate can be applied. Using the spray gun apply 4 or v thin coats of the finish, again allowing time for information technology to dry between each glaze. The stop seals the colourant in the leather preventing it from wearing and prolongs the leathers life.
When complete, let 24 hours before using the item, to ensure the filler, colourant and finish have cured sufficiently.
In improver to the Leather Repair Kit, the Small Leather Colourant Kit was used to colour this job every bit the expanse beingness repaired was quite large and required spraying.
Source: https://www.furnitureclinic.co.uk/e-learning/how-to-fix-a-hole-in-a-leather-car-seat/
Posted by: andrewsmuffe1948.blogspot.com
0 Response to "How To Repair Torn Leather Seat In Car"
Post a Comment